Monday, 5 June 2017

Ribbon spool gift holder..


Happy Monday everyone and what a horrid wet day here in Yorkshire. Apologies in advance for my dark looking photo there simply is no light today ...time to invest in a light tent I think.
So todays project is a special designed holder to gift samples of ribbon. You could send these to a crafty friend or a customer as a sample or as a treat to add to a crafty swap. Or you could send it as a gift everyone loves ribbon, I used to love to tie it in my girls hair when they were small so ribbon is aways useful.

A simple design with spool shaped holders for the ribbon which are easily made using the envelope punch board. A fantastic crafty tool with lots and lots of uses. I used the new powder pink card and shade of Floral DSP , such a pretty delicate and girly colour its hard for me to use other colours just now.

The holder closes with mini magnets which I purchased from Spider magnets on eBay just search disc magnets.

There is a full step by step tutorial on my Youtube channel for you to follow to re create this project. Measurements and supply lists are below. So sit comfy grab a brew and watch the tutorial , I do hope you will try this project out ..... Happy stamping xxxx Amanda

                                 


Supplies with shop links:-

Envelope punch board https://www2.stampinup.com/ecweb/ProductDetails.aspx?dbwsdemoid=5023169productID=133774

Fresh florals DSP https://www2.stampinup.com/ecweb/ProductDetails.aspx?dbwsdemoid=5023169productID=144131

Powder pink A4 card https://www2.stampinup.com/ecweb/ProductDetails.aspx?dbwsdemoid=5023169productID=144251

Label me pretty bundle https://www2.stampinup.com/ecweb/ProductDetails.aspx?dbwsdemoid=5023169productID=145305

Measurements:-

Holder :- cut full length of a4 sheet at 31/2" wide, sore on long side at 3 1/2- 4 1/2 - 4 3/4 -9 1/4 and 9 1/2"

DSP panels:- one at 3 1/4 x 31/4 ", one at 3 1/4 x 2", one at 4 1/4 x 3 1/4"

Spools :-cut card 3 x 4 7/16ths" minimum two of these . Using the punch board punch one end at
1 1/2" on bothe sides then punch the other end at 1"... Score the 1 1/2" end at 1"

to make holes find the centre point of the spine and punch holes at equal distance use these holes to do same hole measurements on your spools ...this will depend on the type of hole punch you have but if you watch my Youtube video you will see how I did it.






6 comments:

  1. Hi Amanda, just watched this on FB thought I'd have a little wonder over here too. I think this is lovely, but I could only give it to special people, cos I would want to keep the lace & or ribbon 🎀 Haha but it is lovely & I love the colour, sometimes, I think, it's what colours you use, that keep people's interest xxx

    ReplyDelete
    Replies
    1. Ha ha ha ha your supposed to SHARE Sandra xxx A

      Delete
  2. Greetings from the US & happy Monday,
    We'll done Amanda!
    Thank you for sharing this sweet & clever gifting idea!
    Have a wonderfully crafty week!

    ReplyDelete
    Replies
    1. Hi Lois and thank you sweetie xx Amanda

      Delete
  3. I'm the only one fussing about this, but the panel measurement is wrong on the 3-1/4 x 2. It's too big. I checked my scoring 10x too. There's only 1-1/2" at the end after the 9-1/2" score line since we're working with an 11 x 3-1/2 piece of card stock, so my math is right. Help?

    ReplyDelete
    Replies
    1. no honey I'm used UK A4 size so its larger than 11 inch I'm assuming your in the USA so our A4 measure 29.7 cm long ... hope this clears it up for you ... my measurements are correct to UK A4 which I did say in my video and showed the measurement on the score board if you look carefully as I was aware it may vary for US measurements xx Amanda

      Delete